TS and RT plus thicknesser workbench

[ryobi]

My TS and RT plus thicknesser project. I want to build may own complete wood working table it measure 28 x 60 inc. long I will start at the flat form with 4 wheels. I copy this from other forum which he used MDF board. I think it is required for MDF board if used as a flat form to make it strong base
So I used plyboard for the plat form and cut it into 28 x 60 inch long

http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4859.jpg

And here is a plan that I got on the other forum so I have as reference
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4860.jpg

And here it is strait flute 3/4 router bits that I used on my router on this plyboard woooweee lot lots of woods dust hehehe and of course I use safety eye goggles to protect my SORE EYES hehehe mask and globs for my safety and health also. It was very hard to breading you will inhale lots of woods dust if don’t have a mask ….

http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4861.jpg

http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4863.jpg

[ryobi]

I have lots old scrap plywood’s and I don’t want to throw into garbage or make it as a panggatong hehehe so I cut it into 4 inch. Strip with my TS and cut it with respective size wit my sliding mitre and then wood glue and gun nailer for the divider
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4865.jpg

http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4864.jpg

And now to cover it with 1/2 marine plywood
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4868.jpg

Before I cover it I applied with clear solignum to make it sure that there is no termite will eat my plywood it seam that most of divider are old plywoods or used plywoods that I used ..
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4866.jpg

[ryobi]

And cut the 4 corner so the wheel can mount on it
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4869.jpg

Glue on top of the divider
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4870.jpg

Nailed
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4872.jpg
4 inch wheels with lock
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4875.jpg

[ryobi]

And ready to roll now.... hmmm where I put it on a safe place that my wife cant see it hehehe ohhh !!! my eyes is aching now need to rest muna and study my plan for more details hehehe:D
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4876.jpg


http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4877.jpg

cheers:)

[timber715]

reduce your picture size thru photobucket, we cannot understand most of the writings kasi. try to limit them to 480x640pixels para hindi mag resize ang thread.

[beebeenator]

You just made a Torsion Box for the base. Nice work

[pyth]

very nice bro..parang gusto ko na rin mag post ng may newbie projects..

[ernie_serrano]

sir, curious lang, how much would a thcknesser ng Ryobi Cost and san nakaka bili?

kaya ba nya mga hard wood? i usually play with the likes of yakal, narra, molave etc.

[ryobi]

sir, curious lang, how much would a thcknesser ng Ryobi Cost and san nakaka bili?

kaya ba nya mga hard wood? i usually play with the likes of yakal, narra, molave etc.


sir ernie cost of ryobi thicknesser around 6k to 7k..performance no problem from hardwood like yakal narra and others

:)

[ryobi]

Okay for continuation of my project installed 2x 2 angle bar at both end of the platform for additional strength of the base
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4883.jpg

http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4882.jpg

I used marine plywood ¾ thick 16 x 28 inc. square board and mounted with bolt and nuts
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4889.jpg

[ryobi]

and make a tenon
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4888.jpg

measured the actual distance for mortising
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4890-1.jpg

and mortise
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4891.jpg

and mounted
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4892.jpg

[ryobi]

and here it is
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4893.jpg
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4894.jpg

and then for the router table same procedure done in tablesaw
http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4895.jpg

http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4896.jpg

[ryobi]

http://i873.photobucket.com/albums/ab296/rtirona/table%20saw/100_4898.jpg

[beebeenator]

looking good :)

but your last pic is oversized :P

[beebeenator]

Ryobi

yung ginamit mo na bit for the router. What is the size? coz a 3/4 straight bit is actually larger than a 3/4 plywood.

[timber715]

hmmm pano yung router table? wala pa yung inserts eh.... hehehehe, coming soon na bro :D

[ryobi]

hmmm pano yung router table? wala pa yung inserts eh.... hehehehe, coming soon na bro :D

excited na nga ..:) just prepare para naka ready na ung table ;)

[ryobi]

Ryobi

yung ginamit mo na bit for the router. What is the size? coz a 3/4 straight bit is actually larger than a 3/4 plywood.

3/4 is oversize para sa 3/4 plywood maluwag i used 5/8 staight bit ung remaining na 1/16 trim just to fit 3/4 plywood

[beebeenator]

ahhhh i see, thanks Ryobi.

I am seriously contemplating on getting a ryobi table saw.....

[ryobi]

ahhhh i see, thanks Ryobi.

I am seriously contemplating on getting a ryobi table saw.....

i think you must see this link ...it was really better than mine but same brand ...i need to modify may ts like zero insert plate but this one it has already replaceable insert plate
http://www.**************/index.php/view+classifieds/id/2308718/RYOBI+TABLE+SAW+WITH+EXTENDABLE+CARRIAGE+AND+COMPL ETE+ACCESSORIES?referralKeywords=table+saw

[ply user]

sir ernie cost of ryobi thicknesser around 6k to 7k..performance no problem from hardwood like yakal narra and others

:)

sir ernie, i got mine from xmart corp for 5,500. search mo sa sulit.com.