Reason for selling?
The infeed and out feed table are NOT perfectly leveled Hence Buyer will have to find a way to level them.
This is what i mean about not level, the infeed table itself has a low spot. Same goes with the outfeed table, it has a low spot. Hence the tops needs to be remachined.
There is a crack in one of the bolting points
This is variable speed
I got this for 15K and i would sell it for 5K.
Its 220volts
Re: Johnson elektrik 6" bench top jointer
Pwede pa hold for two days lang ben, will check funds...
click my signature and it will take you there........
Re: Johnson elektrik 6" bench top jointer
No problem Timber
Re: Johnson elektrik 6" bench top jointer
Good am sir beebeenator, pardon me for being ignorant in serious woodworking, can you pls tell me in a simple way what a bench top jointer is and what is it for.
reply will be appreciated, honestly I don't know what that thing is for.
Thank you again.
CIGWELD Weldskill 250 amp Mig Welder
AHP Alpha-TIG 200X welder
HITRONIC 300 Amp DC Inverter IGBT Welder
YAMATO 300 amp AC Stick Welder
YAMATO 200 amp DC Inverter IGBT Welder
DeWALT Chopsaw
HOBART and ESAB Welding Helmets
cloned STIHLs
MS 044 chainsaw
MS 070 chainsaw
Re: Johnson elektrik 6" bench top jointer
Timber,
I am also open for swapping
Rosy,
A jointer is used for squaring the face or edge of a stock. squaring means making one side of a stock perfectly straight and flat.
The reason i emphasized the low points in the infeed and outfeed table is because if these are not perfectly squared themselves it makes it harder to run a stock to make it square.
I also found not much use for it since i do my "jointing" in the table saw with a jig.
I hope I was able to clearly explain it, Just ask away if you have any more questions 🙂
Re: Johnson elektrik 6" bench top jointer
It functions like a hand planer (powered hand plane.) Except it's upside down. So you move the wood from infeed to outfeed ala tablesaw. Run a piece through it and you should get one flat side. Referencing against the the fence, and you'll "joint" one side perfectly 90's to the flat side.
After this, it's off to the thickness planer (like makita 2012nb) for the other sides. You now have a properly milled/dimensioned lumber.
Re: Johnson elektrik 6" bench top jointer
@ sir beebeenator
@ sir owyn
Thanks a lot for the infos and explanation, its quite enlghtening,
sorry for the ignorance. Alam ko lang kasi ay basic woodworking and carpentry you know the usual hammer, nail, hand saw, wooden katam and squares, the basic simple stuffs, etc. The tools you show in your woodshops does really fascinates me.
Hope someday I'll be good also in woodworking and also have the great tools that you have accumulated all this past years.
Well anyway thanks again for the informations.
CIGWELD Weldskill 250 amp Mig Welder
AHP Alpha-TIG 200X welder
HITRONIC 300 Amp DC Inverter IGBT Welder
YAMATO 300 amp AC Stick Welder
YAMATO 200 amp DC Inverter IGBT Welder
DeWALT Chopsaw
HOBART and ESAB Welding Helmets
cloned STIHLs
MS 044 chainsaw
MS 070 chainsaw
Re: Johnson elektrik 6" bench top jointer
you are welcome Rosy 🙂
By the way the jointer is now sold to Timber!!
Re: Johnson elektrik 6" bench top jointer
you are welcome Rosy 🙂
By the way the jointer is now sold to Timber!!
Thanks Ben, see you later...
click my signature and it will take you there........
Re: Johnson elektrik 6" bench top jointer
Got it and with Chisel around, we were able to square the infeed and outfeed, even got the blade adjusted... still need some tweaking but purrs like a cat already...
Thanks Ben
click my signature and it will take you there........
Re: Johnson elektrik 6" bench top jointer
I am relieved that you got it running very well 🙂 i am very happy with the Bosch ixo screwdriver. That little thing can drive a gypsum screw in a two inch tanguile without a pilot hole!
What did you guys do to square the table tops? Don't tell me you filed it?
Re: Johnson elektrik 6" bench top jointer
I am relieved that you got it running very well 🙂 i am very happy with the Bosch ixo screwdriver. That little thing can drive a gypsum screw in a two inch tanguile without a pilot hole!
What did you guys do to square the table tops? Don't tell me you filed it?
we removed the infeed and cleaned them... 😀
click my signature and it will take you there........
Re: Johnson elektrik 6" bench top jointer
Hahahaha Im glad it will now be used, for the lOngest time it's just been sitting idle and I do all small scale monthly in the table saw with a jig
Re: Johnson elektrik 6" bench top jointer*SOLD
@timber,
wow sweet jointer! is the fence adjustable?
The devil will find work for idle hands to do.-Morrissey
Re: Johnson elektrik 6" bench top jointer*SOLD
@timber,
wow sweet jointer! is the fence adjustable?
yup it is Doc V.called Moji already so I can borrow his straight edge so I can align everything...
click my signature and it will take you there........
