mga sir alam niyo po ba kug ano pang putol sa Aluminum composite, yung ginagamit pang cladding. thanks
Re: Cutting Aluminum Composite
That will depend on the thickness of your aluminum composite. If they are the thin type about gauge 18, 20, or 26, probably you can use your hand tool snips. But if its gonna be thicker you have to have an electric shear or a jig saw, lets say up to gauge 14 but for more thicker ones, say 3/16" or 1/4" and above, it will need already a very special mechanized precision cutter with a carbide tip blades. 😉
Say a circular saw with carbide tip blades.
Try researching it in the net or Google search mo, I'm pretty sure you will find the answer you seek. :rolleyes:
CIGWELD Weldskill 250 amp Mig Welder
AHP Alpha-TIG 200X welder
HITRONIC 300 Amp DC Inverter IGBT Welder
YAMATO 300 amp AC Stick Welder
YAMATO 200 amp DC Inverter IGBT Welder
DeWALT Chopsaw
HOBART and ESAB Welding Helmets
cloned STIHLs
MS 044 chainsaw
MS 070 chainsaw
Re: Cutting Aluminum Composite
Hi
None ferrous saw blade triple chip grind. Yung tip alternate trapezoid and flat. The thicker the better against sound and force. To make bends router bits vee cutter for sharp folds or round tip for soft bends. Make yourself a bending tool made of aluminium angle extrusions. Iwasang pukpukin halata ang tama.
Installed a few machines for processing said material.
Cheers
Re: Cutting Aluminum Composite
Hi
None ferrous saw blade triple chip grind. Yung tip alternate trapezoid and flat. The thicker the better against sound and force. To make bends router bits vee cutter for sharp folds or round tip for soft bends. Make yourself a bending tool made of aluminium angle extrusions. Iwasang pukpukin halata ang tama.
Installed a few machines for processing said material.
Cheers
Sir pardon may ignorance, meron po bang ganyan na bala para sa jigsaw? yun kasi balak kong gamitin palitan ko yung talim. tia
Re: Cutting Aluminum Composite
Naku malabo yata. Kasi ang action ng Jig saw is similar sa lagereng bakal (Hack Saw) or Band Saw. magkakaroon ng tearing sa aluminium which could delaminate the neoprene core plus following a line with a jig saw is an art form meaning it will not be straight. I wouldnt recommend it. The minimum equipment to cut should be a circular saw with a fine TCT blade.
Re: Cutting Aluminum Composite
@ stambudu... bakit di mo subukan? merong jigsaw blade for cutting none ferrous metal... maghanap ka ng scrap na aluminum composite panel. saka lagariin mo sa jigsaw mo. gumamit ka lang ng guide para straight... router man o circular saw ang gamitin, hindi rin straight kung walang guide.
Re: Cutting Aluminum Composite
@ stambudu,
Bro, fortnapz has a point there, the only secret there is the straight edge guide whether for a jig saw, an ordinary circular saw or a worm drive circular saw or a router unless you will have curves to cut that you have to use freehand but otherwise it is still the straight edge guide, or the track.
%3Bhttp%253A%252F%252Fforum.woodenboat.com%252Fshowthread.php%253F121294-Should-I-spring-for-a-worm-drive-circular-saw%3B792%3B542
%3Bhttp%253A%252F%252Fwww.lulusoso.com%252Fproducts%252FCircular-Saw-Guide-Homemad.html%3B1398%3B1194
http://www.shopsmith.com/ownersite/catalog/track_saw_system.htm
CIGWELD Weldskill 250 amp Mig Welder
AHP Alpha-TIG 200X welder
HITRONIC 300 Amp DC Inverter IGBT Welder
YAMATO 300 amp AC Stick Welder
YAMATO 200 amp DC Inverter IGBT Welder
DeWALT Chopsaw
HOBART and ESAB Welding Helmets
cloned STIHLs
MS 044 chainsaw
MS 070 chainsaw
Re: Cutting Aluminum Composite
nagakawa Máy lannhj chÃ*nh hãng m?i 100% giá r? - V? sinh máy l?nh ch? 80k - Di?n l?nh ABC 0977160246
Re: Cutting Aluminum Composite
Mukhang mapapabili ako ng circular saw talaga para sa project na ito. thank you mga sir sa input.
Re: Cutting Aluminum Composite
Sorry, that reply was incomplete was also wrenching my hobby, anyway there are a few issues when using a track guide on alucobond first the blade should show the full gullet of the blade to allow chip evacuation with that in mind you will need a hard foam board para patungan ng aluminium. Dahil di pwede rin ipatong lang sa saw horse madaling magbakat ang dents. With a track guide you also have to clamp the track on the panel again if not careful, dents.
Attach the circular or router under a 1/2" 4x8 plywood and make a rip fence. This will allow you set the fence and do slide cuts like a table saw.
Re: Cutting Aluminum Composite
sửa chữa camera quan sát tại nơi sử dụng giá thanh canh tranh Liên hệ 0902133667
Re: Cutting Aluminum Composite
sửa chữa camera quan sát tại nơi sử dụng toà n quốc
Nhận sửa chữa cung cấp lắp đặt camera quan sát trên toà n quốc
Là đơn vị cung cấp hệ thống camera quan sát chuyên nghiệp trên toà n quốc
Nhằm nâng cao chất lượng phụ vụ quý khách hà ng chung tôi cung cấp thêm dịch vụ sau bán hà ng : sửa chữa camera quan sát tại nơi sử dụng
Quy trình sửa chữa camera quan sát
Khi quý khách gọi đến trung tâm dịch vụ hỗ trợ khách hà ng của chúng tôi quý khách sẽ được trung tâm cử Ãt nhất 2 nhân viên kỹ thuật tới nơi sử dụng để kiểm tra hệ thống camera quan sát của quý khách hà ng
sửa chữa camera giám sát , camera quan sát
Những lỗi có thể khắc phục tại chỗ chúng tôi sẽ xử lý trong thời gian nhanh nhất
Những lỗi không thể khắc phục tại chỗ nhân viên kỹ thuật sẽ bà n giao đầy đủ giấy tờ biên nhận sửa chữa có đóng dấu của công ty chúng tôi và seri máy và nhân viên kỹ thuật sẽ mang máy về để tiến hà ng sửa chữa
Trước khi sửa chữa camera thì chúng tôi sẽ tiến hà nh báo giá cho quý khách rồi mới tiến hà ng sửa
tiêu chà sửa chữa
sửa chữa nhanh nhất
thay thể linh kiện chÃnh hãng
giá thà nh cạnh tranh
bảo hà nh nâu nhất
Nhận sửa chữa camera quan sát toà n quốcsửa chữa camera quan sát tại nơi sử dụng toà n quốc
Nhận sửa chữa cung cấp lắp đặt camera quan sát trên toà n quốc
Là đơn vị cung cấp hệ thống camera quan sát chuyên nghiệp trên toà n quốc
Nhằm nâng cao chất lượng phụ vụ quý khách hà ng chung tôi cung cấp thêm dịch vụ sau bán hà ng : sửa chữa camera quan sát tại nơi sử dụng
Quy trình sửa chữa camera quan sát
Khi quý khách gọi đến trung tâm dịch vụ hỗ trợ khách hà ng của chúng tôi quý khách sẽ được trung tâm cử Ãt nhất 2 nhân viên kỹ thuật tới nơi sử dụng để kiểm tra hệ thống camera quan sát của quý khách hà ng
sửa chữa camera giám sát , camera quan sát
Những lỗi có thể khắc phục tại chỗ chúng tôi sẽ xử lý trong thời gian nhanh nhất
Những lỗi không thể khắc phục tại chỗ nhân viên kỹ thuật sẽ bà n giao đầy đủ giấy tờ biên nhận sửa chữa có đóng dấu của công ty chúng tôi và seri máy và nhân viên kỹ thuật sẽ mang máy về để tiến hà ng sửa chữa
Trước khi sửa chữa camera thì chúng tôi sẽ tiến hà nh báo giá cho quý khách rồi mới tiến hà ng sửa
tiêu chà sửa chữa
sửa chữa nhanh nhất
thay thể linh kiện chÃnh hãng
giá thà nh cạnh tranh
bảo hà nh nâu nhất
Nhận sửa chữa camera quan sát toà n quốc
Re: Cutting Aluminum Composite
i have tried on 3mm ACP pina bagsak ko.. its perfectly cut edge. no bend im not sure if in 4mm thick havent tried it yet.
Does any on have a Bending tool for ACP? we just used Hands to bend it manually. it works well just be careful it might tear.
Re: Cutting Aluminum Composite
Installed a cnc on a shop, heres what i saw. They used an aluminium profile that has a slot that fits the thickness of the panel of different lenghts to bend a corner. For column cladding they used a sheet rolling bender. For cutting they use the following.:
Cnc mounted Circular saw
Cnc Router
Cabinet saw
Jig saw
Shears (gunting ng yero)
Apologies, I stand corrected, you can use jig saws.
Posted via PHM Mobile