Forum

Share:
Notifications
Clear all

TB with tub

18 Posts
8 Users
0 Reactions
130 Views
violaine
(@violaine)
Posts: 1926
Noble Member
Topic starter
 

the last week was fruitful but i forgot to document when we had some hard time installing the tub. i mentioned before in another thread, there is a only a 2cm wall clearance (rough) for the 149cm tub (the idea of a tub came only after building the walls).

good enough my brother gave me some able tile mason to solve the problem.

before we installed, we checked the tub for leaks..if the stock fittings werent ok in the first place, i would have bought a new dedicated set instead.

the tiles now are ready for grouting.

The devil will find work for idle hands to do.-Morrissey

 
Posted : 13/11/2010 8:48 am
violaine
(@violaine)
Posts: 1926
Noble Member
Topic starter
 

Re: T&B with tub

a circular combination lamp &exhaust

a 4" diameter neltex pipe was installed to accomodate the duct

i feel weary to install the wiring as well as the marine plywood ceiling so i told them to go ahead first with the T&B floor tiling and grouting.

The devil will find work for idle hands to do.-Morrissey

 
Posted : 13/11/2010 8:58 am
jarod
(@jarod)
Posts: 1222
Noble Member
 

Re: T&B with tub

a circular combination lamp &exhaust

Nice on Doc! But I think the small entry hole would suffice.

For more of the latest tools, deals and tips - click HERE

 
Posted : 13/11/2010 9:58 am
violaine
(@violaine)
Posts: 1926
Noble Member
Topic starter
 

Re: T&B with tub

bro, the exit duct of the exhaust is 2mm less than 4 inches enough to fit the 4" pipe..will wrap around a duct tape for the final accoutrement.

thanks

The devil will find work for idle hands to do.-Morrissey

 
Posted : 13/11/2010 2:55 pm
 guad
(@guad)
Posts: 646
Honorable Member
 

Re: T&B with tub

Are the light and fan independently controllable? Does it take standard socket bulb/CFL(s). Where is a fixture like that available? Looks like a 10" opening.

Does the foam insulation have reflective foil/film on the top side and an air gap between itself and the underside of the roof?

 
Posted : 13/11/2010 7:40 pm
violaine
(@violaine)
Posts: 1926
Noble Member
Topic starter
 

Re: T&B with tub

@guad,

its a bilayer aluminum foil insulation and we followed the manufacturer's (Airfoam) instruction by installing it putting a little "sag" in between purlins for air circulation.

the air and lamp have independent cables with a ground wire each.

it is fitted with a circular fluorescent lamp with a relatively tight enclosure and diffuser (where insects can enter).

it will be fixed after the paint primer and located the area for the ceiling manhole.

The devil will find work for idle hands to do.-Morrissey

 
Posted : 14/11/2010 2:16 am
 macG
(@macg)
Posts: 82
Trusted Member
 

Re: T&B with tub

a circular combination lamp &exhaust

a 4" diameter neltex pipe was installed to accomodate the duct

i feel weary to install the wiring as well as the marine plywood ceiling so i told them to go ahead first with the T&B floor tiling and grouting.

Hi violaine. Where did you purchase your lamp-exhaust? How much does this cost? I need to install a similar exhaust in my windowless 1st and 2nd floor bathrooms. My only problem is how to do it the 1st floor bathroom. I have created a thread on this, but got no replies yet. I may not know the exact terminologies though 🙁 .

http://www.pinoyhandyman.com/showthread.php?t=1169

 
Posted : 12/12/2010 1:10 pm
violaine
(@violaine)
Posts: 1926
Noble Member
Topic starter
 

Re: T&B with tub

it is available at any Handyman Do it Best store...i was looking for the square type for ease of installation but they have no stock..its 2,700p i think.

i am still not through with the wiring maybe tomorrow...then painting the ceiling perhaps will follow...t&b should be finished before xmas.

too many delays in all of my projects though.

good luck on all your finishing chores.
😉

The devil will find work for idle hands to do.-Morrissey

 
Posted : 12/12/2010 5:51 pm
 macG
(@macg)
Posts: 82
Trusted Member
 

Re: T&B with tub

it is available at any Handyman Do it Best store...i was looking for the square type for ease of installation but they have no stock..its 2,700p i think.

i am still not through with the wiring maybe tomorrow...then painting the ceiling perhaps will follow...t&b should be finished before xmas.

too many delays in all of my projects though.

good luck on all your finishing chores.
😉

Thanks. Will check it out. 🙂

 
Posted : 12/12/2010 9:11 pm
violaine
(@violaine)
Posts: 1926
Noble Member
Topic starter
 

Re: T&B with tub

little work done in this t&b...
painted the ceiling and installed the molding and so my ls1013 found some work today...a precise machine indeed!

crisp cut with a 60 tooth yellow blade

worse..the masonry work isnt at all perfect..near hairline gaps are sometimes a headache..good grief this is just on one corner.
white silicone paintable putty is the best for this problem.

lamp exhaust installed..electricals still to follow.

busy holidays..i work only bit by bit and whenever i can.
thanks be to God...i can still do some woodwork etcetera.
Merry Christman! Godbless you all.

The devil will find work for idle hands to do.-Morrissey

 
Posted : 24/12/2010 7:14 pm
violaine
(@violaine)
Posts: 1926
Noble Member
Topic starter
 

Re: T&B with tub

next will be the installation of the water closet and lavatory and the fittings.

id better enjoy some fruit salad later.
😉

The devil will find work for idle hands to do.-Morrissey

 
Posted : 24/12/2010 7:19 pm
JayL
 JayL
(@jayl)
Posts: 5426
Member
 

Re: T&B with tub

V ... that is what I found out too. More often than not you can't trust carpentry and masonry work here in terms of squareness et al ....

We did a wardrobe cabinet before. Cut all plywood etc in the TS and everything as square as I can make it only to find out that I have fitting problems when I was installing it against the wall because I pre assembled the cabinet.

Succeeding jobs I just let the carpenters go their way. Build as they go along.:(

Millermatic 180 Autoset Mig Welder
Miller Spoolmate 100 Spool Gun
Victor Firepower 350 Oxy Ace Outfit
3M Speedglas 9002X AD Helmet
Makita LC1230 Dry Cut Saw
Ingersoll Rand Air Tools
Snap On Tools
Metabo Power Tools
Norseman Drill Cutting Tools
Bosch Power Tools
3M PPS

 
Posted : 24/12/2010 7:26 pm
violaine
(@violaine)
Posts: 1926
Noble Member
Topic starter
 

Re: T&B with tub

right.
:p

The devil will find work for idle hands to do.-Morrissey

 
Posted : 24/12/2010 7:46 pm
 guad
(@guad)
Posts: 646
Honorable Member
 

Re: T&B with tub

worse..the masonry work isnt at all perfect..near hairline gaps are sometimes a headache..good grief this is just on one corner.

Assuming that the wall is the problem and not the molding, it looks like the wall angle is about 91 degrees (assuming a gap of say half a millimeter at a 3 cm radius).

A one degree error is about 10x more than the error of a carpenter square (which I assume is about 0.1 degree, or ~1 mm in 60 cm), so if we require the mason to raise their accuracy standard to that of a square, their errors should be well below one degree.

At least in theory. Maybe we'll put that to the test in next project...

 
Posted : 25/12/2010 2:05 pm
 moji
(@moji)
Posts: 951
Prominent Member
 

Re: T&B with tub

I read somewhere that carpenters undercut the molding's edge by a small degree.

I don't think masons can square up walls to the accuracy of a degree. It just isn't realistic.

Jay you are correct, built in cabinets really need to be built on site. Cabinets are really exacting if you want it to look good, so a good fit would be necessary. I learned that when building the kitchen cabinets and the walls weren't 90 deg.

Maybe that is another reason carpenter's here are more proficient with hand tools rather than power tools. They always need to compensate for the deficiencies of the masonry work.

 
Posted : 25/12/2010 3:56 pm
Page 1 / 2
Share: