Preparing the bottom frame..1-1/2"x2mm square tubing, a scrap material that i used in my previous project..
Medyo matatagalan to kaya nag apply muna ako ng rust converter..
Dito ko ipapasok ang wheel shaft..
Na galing sa chopsaw stand ko..hehehe..
Posted via PHM Mobile
Re: MIG Cart
The hole made by 5/8 drill bit is not big enough to accommodate the wheel shaft so i use my straight grinder to enlarge the hole..ayan shoot na sya..
Fabricating wheel casters mount..
5mm plate..dito ko ipapatong yung gas tank..
Kaya nakalabas ang small wheel para makapag adjust ako..kailangan equal ang height..
Posted via PHM Mobile
Re: MIG Cart
Di lng pala sa sa baby maganda ang petroleum jelly..pwede ring alternative as mig nozzle gel..lol!
Straight pull..na missed ko pa yung bottom edge..grind and re weld ulit..
Then i made a short bead run in 5mm plate,sa loob para walang makita sa labas na hinang..
Dami ng pics..wala pa namang nagagawa..stop muna ako jan..wala ng materyales.
Posted via PHM Mobile
Re: MIG Cart
The hole made by 5/8 drill bit is not big enough to accommodate the wheel shaft so i use my straight grinder to enlarge the hole..ayan shoot na sya..
Fabricating wheel casters mount..
Posted via PHM Mobile
Uuyyyy, na umpisahan na ng mama yung Mig Cart, nice front and rear mount fabrication, but I am kinda curious about the rear axle, why use a corrugated steel bar instead of a round bar stock ? Is that a 16 mm steel rebar bro ? :confused:
Thanks !! :thanks:
CIGWELD Weldskill 250 amp Mig Welder
AHP Alpha-TIG 200X welder
HITRONIC 300 Amp DC Inverter IGBT Welder
YAMATO 300 amp AC Stick Welder
YAMATO 200 amp DC Inverter IGBT Welder
DeWALT Chopsaw
HOBART and ESAB Welding Helmets
cloned STIHLs
MS 044 chainsaw
MS 070 chainsaw
Re: MIG Cart
Yan kasi ang fit sa butas ng wheel bearing sir..pag nabuo yan di nyo na makikita yan,hehehe..
Sent from my iPad using Tapatalk
Re: MIG Cart
AH OK, Hindi ko naman sinasabing mali or panget and pagka gawa, its just unusual. I know it will be covered anyway by a plate so nobody will see it anymore.
Just enjoy the cart built !! 😀
CIGWELD Weldskill 250 amp Mig Welder
AHP Alpha-TIG 200X welder
HITRONIC 300 Amp DC Inverter IGBT Welder
YAMATO 300 amp AC Stick Welder
YAMATO 200 amp DC Inverter IGBT Welder
DeWALT Chopsaw
HOBART and ESAB Welding Helmets
cloned STIHLs
MS 044 chainsaw
MS 070 chainsaw
Re: MIG Cart
All is set and ready to weld..bzzzt! Lol! Yung lang nakalimutan ko na naman buksan ang gas tank..hehe..
Posted via PHM Mobile
Re: MIG Cart
Haay..sarap mag clamp sa lamesa ko..
Yan lang muna sa ngayon..
Posted via PHM Mobile
Re: MIG Cart
Dito ko iiipit ang gas tank..
Posted via PHM Mobile
Re: MIG Cart
May ginawa akong transmision ng hand tractor nung isang araw..kinuha ko yung kadena..
Eto ang aakap sa gas tank..
My original plan is to fasten the chain by bolt..pwede sana pero mahihirapan akong magtangal at mag kabit..pikado kasi..
Kaya ginawa kong pin type na lang..
Posted via PHM Mobile
Re: MIG Cart
Fabricating the pin..
Posted via PHM Mobile
Re: MIG Cart
Ayos!
Shoot..shoot lang..
Posted via PHM Mobile
Re: MIG Cart
Always a good safety measure to protect that inert gas tank at all cost. If for any reason it falls down and the valve breaks then it will fly like a rocket specially if it's still at high pressure. I can't imagine the havoc it will do if this happens when it's at 2,000 psi pressure but I know that cement walls would be like paper.
Millermatic 180 Autoset Mig Welder
Miller Spoolmate 100 Spool Gun
Victor Firepower 350 Oxy Ace Outfit
3M Speedglas 9002X AD Helmet
Makita LC1230 Dry Cut Saw
Ingersoll Rand Air Tools
Snap On Tools
Metabo Power Tools
Norseman Drill Cutting Tools
Bosch Power Tools
3M PPS
Re: MIG Cart
Nice bro bugel 🙂
Sent from my GT-N7100 using Tapatalk
Re: MIG Cart
Hhmmnn, nice idea sir, di ko pa na try petroleum jelly, but what I did before was get a small cup and spray the contents of WD40 unto it until I get about enough to dunk the nozzle in. After about 30 minutes of continuous run on a drill pipe, it's just about time to clean the contact tip as well. I take out the nozzle, clean the spatter on the inside surface and dunk it into the WD40. While it's cooling, its a good time to the contact tip as well. Malaki talaga ang difference pag nai-dip mo cya sa WD40, pag tinangal mo ung spatter from the inside, buong buo cya parang sing-sing.
