Forum

Share:
Notifications
Clear all

My journey into welding with the Asea 200TIG

24 Posts
6 Users
0 Reactions
127 Views
(@bryant77)
Posts: 480
Reputable Member
 

Re: My journey into welding with the Asea 200TIG

Timb where did you get the Tajima Magnetic Holder?

 
Posted : 17/08/2011 8:11 pm
timber715
(@timber715)
Posts: 5424
Member
Topic starter
 

Re: My journey into welding with the Asea 200TIG

I did wear my welding helmet Jay though I was in shorts hehehehe. ang init ng shrapnel... :branch:

Bryant, sa Recto store lang natisod yan, was asking for another pero wala na. naligaw lang brader. hehehehe
:consoling2:


click my signature and it will take you there........

 
Posted : 17/08/2011 11:56 pm
timber715
(@timber715)
Posts: 5424
Member
Topic starter
 

Re: My journey into welding with the Asea 200TIG

found some grinding stones today during my walks. 6mm and fits perfect.

the wrong way to hold the grinder...

the legs welded and waiting for an angle grinder for clean-up....


click my signature and it will take you there........

 
Posted : 18/08/2011 1:58 am
(@xyname)
Posts: 9
Active Member
 

Re: My journey into welding with the Asea 200TIG

wow, nice tools

im a welding newbie myself, (just started this summer)

 
Posted : 19/08/2011 10:05 am
timber715
(@timber715)
Posts: 5424
Member
Topic starter
 

Re: My journey into welding with the Asea 200TIG

all I did today(since I arrived late for work) was make these...

needed to make a few so I got some weld time...

the welds came out fine and had only one burn thru which I immediately welded shut. welds were minimal and slag wasn't an issue since I used 6011 rods.

some cleaning required.


click my signature and it will take you there........

 
Posted : 20/10/2011 1:56 am
timber715
(@timber715)
Posts: 5424
Member
Topic starter
 

Re: My journey into welding with the Asea 200TIG

cut off a bit more than I needed, but all welds were solid which was a pleasant surprise.

drilled holes on the sides for mounting then brushed them with primer. also in the picture is the hangers I got free....

drilled some holes again this time on the wall, mounted the brackets and viola, some space recovered.

ran out of tox and screws so the rest will mount as soon as I get some. All in all, a good day:dog1:


click my signature and it will take you there........

 
Posted : 20/10/2011 2:01 am
(@jojod818)
Posts: 23
Eminent Member
 

Re: My journey into welding with the Asea 200TIG

You already started welding na pala brader! Me still a total noob... 😀

 
Posted : 27/01/2012 8:53 am
timber715
(@timber715)
Posts: 5424
Member
Topic starter
 

Re: My journey into welding with the Asea 200TIG

You already started welding na pala brader! Me still a total noob... 😀

Welcome JojoD to PHM brader, very nice to have an electronics master in the group... Oo I did start welding already but very far from being an good, lots here to learn as there are experts in the house to learn from...
got some videos about welding I can share, bring a flash drive and I can share it with you when you pass by my area. Session na rin tayo (sama mo si Cal) :rave:

again welcome to PHM brader...


click my signature and it will take you there........

 
Posted : 27/01/2012 12:04 pm
(@jojod818)
Posts: 23
Eminent Member
 

Re: My journey into welding with the Asea 200TIG

Welcome JojoD to PHM brader, very nice to have an electronics master in the group... Oo I did start welding already but very far from being an good, lots here to learn as there are experts in the house to learn from...
got some videos about welding I can share, bring a flash drive and I can share it with you when you pass by my area. Session na rin tayo (sama mo si Cal) :rave:

again welcome to PHM brader...

Thanks for the warm welcome brader! I feel at home already at PHM. 😎

Yup I saw some of the threads and been learning a lot already.

Aba maganda idea yan, sige will bring a flash drive pag napasyal at madinig ulit namin ni Cal si Harbeth. 😉

 
Posted : 27/01/2012 7:45 pm
Page 2 / 2
Share: