Forum

Share:
Notifications
Clear all

1/2 x 3/8 collet adapter

15 Posts
8 Users
0 Reactions
58 Views
(@joey81)
Posts: 1098
Member
Topic starter
 

Any local shops selling this item?

http://www.highlandwoodworking.com/38x12routercolletadapter.aspx

I need it to attach a forstner bit with 3/8 shank to the plunge router. I'll be making a lot of holes
for concealed hinges.

 
Posted : 04/04/2011 8:10 am
violaine
(@violaine)
Posts: 1926
Noble Member
 

Re: 1/2 x 3/8 collet adapter

the lowest speed i think for a variable speed router is 9000RPM.

please observe safety and i dont think that forstners especially that size (32mm for concealed hinges installation) can be used for such a purpose.

but i could be wrong but id rather use a hand drill if i dont have a drill press in case.

The devil will find work for idle hands to do.-Morrissey

 
Posted : 04/04/2011 8:57 am
(@bigfoot2)
Posts: 362
Reputable Member
 

Re: 1/2 x 3/8 collet adapter

How about a drill guide?

Dumb mistakes will always be dumb mistakes, unless . . . . you learn from it, and then it will be learning experience.

 
Posted : 04/04/2011 10:12 am
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: 1/2 x 3/8 collet adapter

Hahaha! I was kind of expecting this type of response. Thanks doc for making me rethink this approach.

My VS router can go down to 8,000 RPM (at least according to the manual). But this is still way beyond the recommended speeds for forstner bits. Did some googling:

For softwood and smallest diameter (less than 1/2) forstner the fastest recommended speed is 2500 RPM. For 1 1/4 and above max is only 700 RPM. I'll be using 1 3/8 diameter for the concealed hinges.

Sayang. The router edge guide and the plunge base seems perfect for this task in the absence of a drill press.

I'll think I should instead work on mounting the VS hand drill to the router's plunge base.

 
Posted : 04/04/2011 10:18 am
timber715
(@timber715)
Posts: 5424
Member
 

Re: 1/2 x 3/8 collet adapter

EZcut actually has a 35mm router bit (not a forstner) precisely to be used for that purpose. I have one and used it several times and works well, but it came with a 1/2" shank. You can use it too on the drill press if you wish without issues. Not even needed to dial it to the lowest speed, though at 22,000rpm, it is too much. I recommend somewhere in the 12,000 rpm or lower.


click my signature and it will take you there........

 
Posted : 04/04/2011 10:35 am
 guad
(@guad)
Posts: 646
Honorable Member
 

Re: 1/2 x 3/8 collet adapter

EZcut actually has a 35mm router bit (not a forstner) precisely to be used for that purpose. I have one and used it several times and works well, but it came with a 1/2" shank.

Is that the Ezcut 'hinge boring bit' #2803? Ezcut website says that the shanks are 10 mm. Is website mistaken?

http://www.router-bits-manufacturer.com/2801.htm

Power Craft also has hinge boring bits in 1/4 and 1/2 shanks (not 10 mm), at about half the cost.

 
Posted : 04/04/2011 11:45 am
timber715
(@timber715)
Posts: 5424
Member
 

Re: 1/2 x 3/8 collet adapter

Is that the Ezcut 'hinge boring bit' #2803? Ezcut website says that the shanks are 10 mm. Is website mistaken?

http://www.router-bits-manufacturer.com/2801.htm

Power Craft also has hinge boring bits in 1/4 and 1/2 shanks (not 10 mm), at about half the cost.

the EZcut cost around 600 pesos, it is similar but not exactly what is pictured. will take pictures later and get the number as well. it is in the shop kasi.


click my signature and it will take you there........

 
Posted : 04/04/2011 12:02 pm
violaine
(@violaine)
Posts: 1926
Noble Member
 

Re: 1/2 x 3/8 collet adapter

that is the answer joey..get the ezcut hinge boring router bit at around 600 bucks...kaya wag mo na itapon ang edge guide.

cheers!

The devil will find work for idle hands to do.-Morrissey

 
Posted : 04/04/2011 12:21 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: 1/2 x 3/8 collet adapter

Great! Meron palang hinge-boring bit. Parang wala nito sa MLCS catalogue. :confused:

Thanks timb, guad! 😎

 
Posted : 04/04/2011 12:22 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: 1/2 x 3/8 collet adapter

Nga pala, saan available ang EZcut bits?

 
Posted : 10/04/2011 5:16 pm
(@jonathanscruz68)
Posts: 1492
Noble Member
 

Re: 1/2 x 3/8 collet adapter

marami sa panda joey, sa LYS, may nakita rin akong some ez-cut bits, but not as many as panda.

 
Posted : 10/04/2011 10:28 pm
 camv
(@camv)
Posts: 93
Trusted Member
 

Re: 1/2 x 3/8 collet adapter

Inquiry lang po, I also need a 1/2" to 3/8" collet adapter, anybody who knows where to buy it?

 
Posted : 11/07/2011 9:44 am
jarod
(@jarod)
Posts: 1222
Noble Member
 

Re: 1/2 x 3/8 collet adapter

Try calling Panda Industrial and Mayon Construction. You may search their contact# in google.

For more of the latest tools, deals and tips - click HERE

 
Posted : 11/07/2011 11:42 am
timber715
(@timber715)
Posts: 5424
Member
 

Re: 1/2 x 3/8 collet adapter

Inquiry lang po, I also need a 1/2" to 3/8" collet adapter, anybody who knows where to buy it?

anong brand po router nyo? Makita sells adapters for their routers, not sure if they would work for yours though....


click my signature and it will take you there........

 
Posted : 12/07/2011 1:57 am
 camv
(@camv)
Posts: 93
Trusted Member
 

Re: 1/2 x 3/8 collet adapter

sir timber & Jarod
thanks for the reply to my inquiry. I have a triton router. I got a good news today, my makita router RP2301FCX just arrived and when I opened the box a 1/2" to 3/8" collet reducer is included in the package. All along I thought only a 1/4" collet adapter was included. I can use now my 3/8" bit..

 
Posted : 14/07/2011 7:29 pm
Share: