Re: Show your tools in action

The Knipex Pliers Wrench

Re: Show your tools in action

Drilled a few holes today and tried the Magnetic cleanup tool.

Pull and the chips fall down

Re: Show your tools in action

Bent Long Nose Vise Grips are perfect when clearance is an issue. Like this stubborn lag bolt screw that keeps spinning thus the nut won't tighten unless I hold it down. In this case the tool of choice was the 9" BLN VG.

Re: Show your tools in action

eto sa kin meron pang kasunod
HUSKY 24'' bar level
EMPIRE 12" polycast rafter square
RYOBI rechargable circular saw
blade cutter, plier , meter and a pencil more to come tools for wood working , electronics projects and some metal works

Re: Show your tools in action

My simple 1/2" MDF circular saw / router sled. Too wide a cut for the TS so out comes the CS.

Long time I did not use this sled and noticed that it got damaged by water. Maybe it's worth to make some new ones in phenolic when I get my cordless circular saw. I know there are other ways to use a circular saw guide but I found the sled to be very quick to setup.

Re: Show your tools in action

Jay the 4100 ts has a cut capacity of 25" di ba? you only cut 5" or less.... subtraction lang brader. hehehehe

Re: Show your tools in action

Jay the 4100 ts has a cut capacity of 25" di ba? you only cut 5" or less.... subtraction lang brader. hehehehe

You mean cut with the small portion against the fence ... LOL . Yes I think I could have done that because the TS is same height as the workbench which I could use for support.

Thanks for the tip bro.

Re: Show your tools in action

You mean cut with the small portion against the fence ... LOL . Yes I think I could have done that because the TS is same height as the workbench which I could use for support.

Thanks for the tip bro.

it is here Jay that you need to consider the blade kerf since you will be using the outer part and not the inner (the inner cut kasi is where the fence is tuned up for)...

Re: Show your tools in action

@jay,

that knipex locking pliers looks awesome. is it still made in germany? i wonder how much it is..yours looks like a 12 incher.

and i never knew there is such a thing as a Bent Long Nose Vise Grips. lol

its cool! a tool for a specific job!

as always in automotive tools...

you're the one!

:bond:

Re: Show your tools in action

@jay,

that knipex locking pliers looks awesome. is it still made in germany? i wonder how much it is..yours looks like a 12 incher.

and i never knew there is such a thing as a Bent Long Nose Vise Grips. lol

its cool! a tool for a specific job!

as always in automotive tools...

you're the one!

:bond:

@V If I can have only one Knipex tool then definitely I will choose the 10" Knipex Pliers Wrench.

http://www.amazon.com/Knipex-8605250-10-Inch-Pliers-Wrench/dp/B000X4J2EI/ref=sr_1_1?ie=UTF8&qid=1314343776&sr=8-1

Re: Show your tools in action

@jay,

i will get one for myself jay.its ratcheting pala!

"kinipek"s pala pronunciation! hehe

thanks bro.

Re: Show your tools in action

@jay,

i will get one for myself jay.its ratcheting pala!

"kinipek"s pala pronunciation! hehe

thanks bro.

Very good tool bro. Yes with a little practice it will ratchet well.

Re: Show your tools in action

Wood glides much better on a TS when the table top is waxed.

Almost perfect 110V power cable organizer for a small wood shop ... at least for my need

I wish I had a reel for air too ... 🙂

Re: Show your tools in action

Dust management ... Phil Tein Baffle ( prototype by MWW Timber715 .... hehehhehe )

I need a way to put all these hoses overhead ....