Forum

Share:
Notifications
Clear all

Baby Crib WIP

23 Posts
9 Users
0 Reactions
101 Views
 camv
(@camv)
Posts: 93
Trusted Member
Topic starter
 

My new Leigh FMT jig just arrived so Im quite excited to put it to the test. I lack the talent of a master handyman so im relying on the new gadgets to make my life easier. I want to start this WIP for quite sometime but when I attempted to make some mortises & tenons I found out this WIP is not easy because it involves a lot of mortising and tenoning. I dont have the luxury of time because my 1st baby is coming very soon! AMAZON is the answer...lol. I told my wife Ill just be the one to build the crib ( thats my justification for buying the Leigh FMT jig and the D4R dovetail jig... I didn't told her the price though hahaha). I bought some other tools with it. In short MY BANK ACCOUNT WAS ROBBED!! by amazon US & UK.

So much for the story, here is my WIP:

The NZ wood that's been sitting idle for months finally moved. I dont have a sturdy workbench yet (I dont have the space for that) so iI'll be using my wobbly B&D workmate.

I'm a little slow in cutting because I double check my measurement before cutting (dont want to waste the precious wood). Then I set up my FMT jig and clamped it to the rockwell jawhorse.

Here are samples of the mortises & tenons I made:

I have no problem watsoever in making tenons, however I frequently experience chatter while routing the ends of the mortises. I did some research and found out that it is a common problem in routing mortises. I should have done some more research before buying the mortising bits. I should have bought 4-flute upcut bits. What I have now are 2-flute upcut bits. To minimize the chatter I slowly plunge route the ends, I can produce good mortises by doing that.

Here is my WIP after 2 days:
I assembled it just to check the fit. So far so good..

Time to take a break... Kakayod muna ng pambili ng wood hehe..
more mortising and tenoning next week.

 
Posted : 17/07/2011 3:21 pm
JayL
 JayL
(@jayl)
Posts: 5426
Member
 

Re: Baby Crib WIP

Hooray ... Mortise and Tenon making up another notch...:attack:

Millermatic 180 Autoset Mig Welder
Miller Spoolmate 100 Spool Gun
Victor Firepower 350 Oxy Ace Outfit
3M Speedglas 9002X AD Helmet
Makita LC1230 Dry Cut Saw
Ingersoll Rand Air Tools
Snap On Tools
Metabo Power Tools
Norseman Drill Cutting Tools
Bosch Power Tools
3M PPS

 
Posted : 17/07/2011 4:51 pm
(@jonathanscruz68)
Posts: 1492
Noble Member
 

Re: Baby Crib WIP

with that super jig you have, you will be creating superb projects with m/t joints...

i'm imagining you'll be achieving your beautiful projects in no time...

missoin arts and crafts, those heirloom pieces...:go::go::go:

:congratualtions:

 
Posted : 17/07/2011 6:21 pm
 camv
(@camv)
Posts: 93
Trusted Member
Topic starter
 

Re: Baby Crib WIP

Sir Jay & Jonathan, this jig makes me more excited about making future projects.. 🙂

 
Posted : 17/07/2011 7:08 pm
violaine
(@violaine)
Posts: 1926
Noble Member
 

Re: Baby Crib WIP

phototips...in using your point and shoots.

pushing the T&W toggle to the extreme wide produces bowing of the horizon due to fish eye view effect

try to move a little farther from the subject to include more of the view then crop it.in this way, the straight lines will appear more straighter.

hey bro..if the stile for example is 48 inches long and you are going to make tenons on both ends..will you need to elevate the whole fmt jig at that height?

😮

The devil will find work for idle hands to do.-Morrissey

 
Posted : 17/07/2011 9:35 pm
 camv
(@camv)
Posts: 93
Trusted Member
Topic starter
 

Re: Baby Crib WIP

@ sir Violaine,
Thanks for the photography tip, I noticed that also.:thanks:
About making tenons on long pieces of wood, the answer is YES you have to elevate it at certain height. But since the parts of the crib is not that long what I did was to clamp the FMT at an inclined position. I've done several times with this WIP. What I have in mind if Ill be making tenons on heavier pieces like bed frame is to bring my Jawhorse at the mezzanine floor and position it near the stairs so that I can place it at inclined position. I imagine I'll be using a vacuum blower to contain the mess or my wife will curse me hehe. It's a trade off. I'll just spend time cleaning the mess just to produce perfect tenons.

 
Posted : 17/07/2011 10:46 pm
violaine
(@violaine)
Posts: 1926
Noble Member
 

Re: Baby Crib WIP

@camv,

thanks for the feedbacks regarding making tenons on long pieces.
we are excited looking forward to the finish product...i am sure we need not caution you on the type of finish you are going to apply for this heirloom project.

i came across this pic..certainly not mine.

The devil will find work for idle hands to do.-Morrissey

 
Posted : 18/07/2011 7:26 am
 guad
(@guad)
Posts: 646
Honorable Member
 

Re: Baby Crib WIP

The NZ wood that's been sitting idle for months finally moved.

Is that untreated NZ wood? Where were you able to get from? The pine usually available in hardware stores in the last few years are all treated.

 
Posted : 18/07/2011 7:31 am
 camv
(@camv)
Posts: 93
Trusted Member
Topic starter
 

Re: Baby Crib WIP

@Violaine,

Thanks for posting this pics, I would love to see my finish project look like this. However I dont know yet how to stain & apply top coat of poly. I've been reding some articles how to do it but still it's different when you're doing it hand-on. All suggestions about staining & finishing will be highly appreciated.

:thanks:

@guad,

This NZ wood are treated and sourced from citi hardware, I've been trying to source out untreated pine wood but I dont have much time roam around (I heard there is a store that sells scrap pine wood somewhere in Teresa, Rizal). Wish I can find cheaper wood..

 
Posted : 19/07/2011 6:35 am
jarod
(@jarod)
Posts: 1222
Noble Member
 

Re: Baby Crib WIP

camv, If you don't mind, how much do those NZ wood cost?

For more of the latest tools, deals and tips - click HERE

 
Posted : 19/07/2011 2:25 pm
 guad
(@guad)
Posts: 646
Honorable Member
 

Re: Baby Crib WIP

This NZ wood are treated and sourced from citi hardware, I've been trying to source out untreated pine wood but I dont have much time roam around (I heard there is a store that sells scrap pine wood somewhere in Teresa, Rizal). Wish I can find cheaper wood.

Did you mean Taytay? But the one(s) there seems to be less favored now compared to the closer one on Ortigas Ave., Rosario, Pasig. Cost ranges from P20-40/bft.

Where to buy good Palo China?
Palochina Sources

 
Posted : 19/07/2011 9:07 pm
(@balarila)
Posts: 1368
Noble Member
 

...i am sure we need not caution you on the type of finish you are going to apply for this heirloom project.

Not sure if Violaine meant the same thing as I do below.

You probably would want to look for non-toxic or food-grade paints for finishing the crib. When my kids were toddlers, I had a tough time looking for such paints. My kids were natural-born gnawlers of bed/crib posts.
Posted via PHM Mobile

 
Posted : 19/07/2011 9:15 pm
Armand
(@armand)
Posts: 837
Prominent Member
 

Re: Baby Crib WIP

very nice crib project..and very nice M/T jig too...the cuts are clean and precise.

 
Posted : 19/07/2011 10:18 pm
 camv
(@camv)
Posts: 93
Trusted Member
Topic starter
 

Re: Baby Crib WIP

@guad,

Yah, you're right. I've read it's in Taytay but haven't tried to look for the place. Pasig is certainly
nearer I try to go there. Thanks for the info. 20-40/bft seems reasonable. So it's now clear to
me that I've been paying an extra premium for the treated NZ wood, almost 3x.:(

@Balarila,
That's my major concern about paints. I've seen cribs with hard plastic cover at the upper portion, im sure to protect the kids from swallowing the paint. Im thinking that I'll just apply 3 coats of poly w/o staining or painting, just the natural color of the wood. Any suggestions about this?

@jarod,
it's about 100/bft.:(
I'll try to look for cheaper wood after completing this WIP.

 
Posted : 21/07/2011 12:17 pm
 camv
(@camv)
Posts: 93
Trusted Member
Topic starter
 

Update:
I need strips of wood to be used as fence for the crib but I cant find appropriately sized pinewood strips at the hardware. Since I dont have a table saw or a bandsaw I decided to improvise. Circular saw con table saw.

Drilled 4 holes on the circular saw baseplate for mounting bolts & nuts.

Mount it in a plank of wood in inverted position. Clamped fence with 3/8" distance from the blade

Presto! I have a table saw:)

After 180+ M&T's my WIP looks like a crib now

 
Posted : 18/08/2011 2:53 am
Page 1 / 2
Share: