Forum

Share:
Notifications
Clear all

Piano box

50 Posts
10 Users
0 Reactions
176 Views
 moji
(@moji)
Posts: 951
Prominent Member
Topic starter
 

Re: Piano box

Got some work done today,

Handplaned the mahogany to make it square

Cut to strips..this would have been waaay faster and easier with a table saw..but i have none so the jigsaw will have to do..

I sanded the box parts to 220 grit with the ROS...now its quite smooth..

 
Posted : 09/06/2010 2:27 am
jarod
(@jarod)
Posts: 1222
Noble Member
 

Re: Piano box

Very nice build and alterntive tips.

I noticed your pretty saw horse, are there still available units of these around?

For more of the latest tools, deals and tips - click HERE

 
Posted : 09/06/2010 1:01 pm
(@beebeenator)
Posts: 1468
Noble Member
 

Re: Piano box

i saw one dati sa Wilcon libis. I think there are two sizes. But i havent seen it lately

One disadvantage is that its not as stable as one would want but the jaws are really neat. It also has dog holes

 
Posted : 09/06/2010 5:32 pm
 moji
(@moji)
Posts: 951
Prominent Member
Topic starter
 

Re: Piano box

i don't know if they still sell the workmate..i haven't seen them around lately..got this at true value.

 
Posted : 09/06/2010 10:48 pm
 moji
(@moji)
Posts: 951
Prominent Member
Topic starter
 

Re: Piano box

Done a bit of work on the box lately but still not done

Glue up of the box. It sucks if you have too little clamps. At least it glued up properly.

trimmed the excess after drying

 
Posted : 29/06/2010 12:10 am
 moji
(@moji)
Posts: 951
Prominent Member
Topic starter
 

Re: Piano box

Now to focus on the lid.

Cut the miters on the cms

Mock up of the lid with the piano keys.

 
Posted : 29/06/2010 12:13 am
 moji
(@moji)
Posts: 951
Prominent Member
Topic starter
 

Re: Piano box

The rear of the lid will be a solid piece of mahogany which would also cover part of the keys.

Cut the mahogany to rough size. Im really happy i got the cms..its one of my most used power tools..

Flattened one side. The grain was very nice on this one

To finish the other side, i marked the width i want then plane to the line

 
Posted : 29/06/2010 12:23 am
timber715
(@timber715)
Posts: 5424
Member
 

Re: Piano box

nice work Moji, I assume you had difficulty cleaning the excess off the endgrain of the finger joints? I use chisels to pare them clean them until it is low enough for the block plane, it avoids tears...


click my signature and it will take you there........

 
Posted : 29/06/2010 12:23 am
 moji
(@moji)
Posts: 951
Prominent Member
Topic starter
 

Re: Piano box

Finish off with a smoothing plane

 
Posted : 29/06/2010 12:24 am
 moji
(@moji)
Posts: 951
Prominent Member
Topic starter
 

Re: Piano box

nice work Moji, I assume you had difficulty cleaning the excess off the endgrain of the finger joints? I use chisels to pare them clean them until it is low enough for the block plane, it avoids tears...

It was a bit difficult..I planed towards the center of the box and tightened up the mouth on my block plane to minimize tears. Good thing too that my block plane is low angle.

 
Posted : 29/06/2010 12:26 am
 moji
(@moji)
Posts: 951
Prominent Member
Topic starter
 

Re: Piano box

Not much time to work on this as i would like, but i spilled some BLO on my work table while doing something else. So instead of letting it go to waste, i applied it to the inside of the box. The chatoyance of the dao and ribbon grain ply made me excited about finishing this project.



 
Posted : 16/07/2010 1:57 am
JayL
 JayL
(@jayl)
Posts: 5426
Member
 

Re: Piano box

To me it came out Great Moji.

Millermatic 180 Autoset Mig Welder
Miller Spoolmate 100 Spool Gun
Victor Firepower 350 Oxy Ace Outfit
3M Speedglas 9002X AD Helmet
Makita LC1230 Dry Cut Saw
Ingersoll Rand Air Tools
Snap On Tools
Metabo Power Tools
Norseman Drill Cutting Tools
Bosch Power Tools
3M PPS

 
Posted : 16/07/2010 2:39 am
(@john-jo)
Posts: 107
Estimable Member
 

Re: Piano box

Its a superb piece of work. Bravo !

 
Posted : 16/07/2010 1:16 pm
(@jonathanscruz68)
Posts: 1492
Noble Member
 

Re: Piano box

sir moji,i've noticed your handplanes.is some of your stuff shopmade?gara kasi ng handplanes mo,especially the stickered once...familiar lang kasi ako sa stanley planes,at sa mga handmade na nakikita ko na binebenta sa bangketa...looking firward to see you guys.thanks

 
Posted : 22/07/2010 6:13 am
 moji
(@moji)
Posts: 951
Prominent Member
Topic starter
 

Re: Piano box

sir moji,i've noticed your handplanes.is some of your stuff shopmade?gara kasi ng handplanes mo,especially the stickered once...familiar lang kasi ako sa stanley planes,at sa mga handmade na nakikita ko na binebenta sa bangketa...looking firward to see you guys.thanks

My handplanes were all bought, those wooden planes that you mention are Mujingfang planes which i got in Hong Kong and are also available online. I actually don't have any shopmade planes but i would want to make one in the future. Maybe something like a Krenov style handplane..

 
Posted : 24/07/2010 6:26 pm
Page 2 / 4
Share: