Forum

Share:
Notifications
Clear all

Wooden Jigs Knobs

13 Posts
6 Users
0 Reactions
62 Views
chisel
(@chisel)
Posts: 471
Reputable Member
Topic starter
 

I have ¼” diameter T bolts but the problem is I don’t have knobs, don’t have the budget na to buy knobs at rockler so decided to make my own. Since I have the lathe might as well fabricate wooden knobs.

Start with 1 ½” x 1 ½” square wood stock drilled 3/8” hole at the exact center.

For this knot coupling to be inserted.

My first attempt I used T Knot but the problem with it is its very hard to center on the hole.

After applying CA to the bolt I made a face plate with a ¼” bolt for the stock to attach.

 
Posted : 13/12/2011 1:30 pm
chisel
(@chisel)
Posts: 471
Reputable Member
Topic starter
 

Re: Wooden Jigs Knobs

Rounding the square stock.

And here where I stop think this shape is perfect.

Then apply finish before I remove it to the lathe.

Finish all six knobs but not satisfied with the shape because it tends to resemblance drawer knob.

 
Posted : 13/12/2011 1:31 pm
chisel
(@chisel)
Posts: 471
Reputable Member
Topic starter
 

Re: Wooden Jigs Knobs

So decided to put groves on the outer sides for fingers to hold on and it made me justify the installation of the miter slot on the router table because I’m gonna need it to build the jig.

Start with wood screw to the miter gauge and drill ¼” hole for the bolt to be screw it will act to hold the knobs in place, notice that the bolt is in the “0” mark of the router plate to establish the center of the router bit.

Then attach my firs knob.

With a ½ cove bit I slowly run the stock to form a star like pattern.

 
Posted : 13/12/2011 1:32 pm
chisel
(@chisel)
Posts: 471
Reputable Member
Topic starter
 

Re: Wooden Jigs Knobs

Then slightly adjust the bit to deepen the grove.

Finished all six knobs. And complement to my shop made feather board.

 
Posted : 13/12/2011 1:33 pm
chisel
(@chisel)
Posts: 471
Reputable Member
Topic starter
 

Re: Wooden Jigs Knobs

Save some money there and kinda fun to build.

Of course I can make a five lobe knob but the degree of rotation is kinda difficult since this is my first try I will settle on a 6 lobe knob.

 
Posted : 13/12/2011 1:34 pm
(@unychorn)
Posts: 61
Trusted Member
 

Re: Wooden Jigs Knobs

wow ganda sir

Mark

 
Posted : 13/12/2011 3:16 pm
timber715
(@timber715)
Posts: 5424
Member
 

Re: Wooden Jigs Knobs

Fancy smancy, ganda brader. I believe I can make something similar even without a lathe... hmmm I'll call the challenge and raise you :naughty: a pair...


click my signature and it will take you there........

 
Posted : 14/12/2011 12:00 am
 owyn
(@owyn)
Posts: 237
Estimable Member
 

Re: Wooden Jigs Knobs

Are the t-bolts locally available Chisel? And yep, they sure look proportional/nice =).

 
Posted : 14/12/2011 12:05 am
chisel
(@chisel)
Posts: 471
Reputable Member
Topic starter
 

Re: Wooden Jigs Knobs

owyn not available locally but you can fabricate one out of a hex bolt

 
Posted : 15/12/2011 1:47 pm
chisel
(@chisel)
Posts: 471
Reputable Member
Topic starter
 

Re: Wooden Jigs Knobs

Fancy smancy, ganda brader. I believe I can make something similar even without a lathe... hmmm I'll call the challenge and raise you :naughty: a pair...

GO.GO.GO.....:go::go::cheerleader3:

 
Posted : 15/12/2011 1:49 pm
violaine
(@violaine)
Posts: 1926
Noble Member
 

Re: Wooden Jigs Knobs

I dont have lathe and thinking i could duplicate your wonderful knobs using a commercial 1" dowels at most homedepots.

thanks for the great tip!

V

The devil will find work for idle hands to do.-Morrissey

 
Posted : 17/12/2011 7:45 am
rosy
 rosy
(@rosy)
Posts: 4307
Member
 

Re: Wooden Jigs Knobs

OOOOOHHHHHHLALA, what lovely and fancy wooden knobs you've made there bro chisel, another peso saving project, very nice tips for other members.

Great and thanks for sharing this !!!!

CIGWELD Weldskill 250 amp Mig Welder
AHP Alpha-TIG 200X welder
HITRONIC 300 Amp DC Inverter IGBT Welder
YAMATO 300 amp AC Stick Welder
YAMATO 200 amp DC Inverter IGBT Welder
DeWALT Chopsaw
HOBART and ESAB Welding Helmets
cloned STIHLs
MS 044 chainsaw
MS 070 chainsaw

 
Posted : 17/12/2011 1:30 pm
chisel
(@chisel)
Posts: 471
Reputable Member
Topic starter
 

Re: Wooden Jigs Knobs

Thanks V & Rosy don't have a lot of use to my lathe eh kaya pinag tripan ko. any way V dare to take the challenge of building one he,he,he....:thanks:

 
Posted : 18/12/2011 10:27 am
Share: