Manufacturer's Specs:
Amperage 15 Amp
Arbor Size 5/8"
Bevel Angle Range -2° to 47°
Blade Diameter 10"
Dado Capacity 1/2"
Depth of Cut at 90 Deg. 3-1/8"
Dimensions 22.5” W x 22.5” D x 13” H
Max. Motor HP 4.0
No Load RPM 5,000
Rating 120 V
Ripping CapacityLeft 7-3/4"
Ripping CapacityRight 18"
Table Top Dimensions 22.5” W x 20” D
Weight of Saw (lbs.) 52
Re: Bosch GTS1031 10-inch Table Saw
Forgot to take pictures of it before use. 🙁
So fast forward.....
Here's the riving knife in the non-tru cut position
Fully raised for use with the anti-kickback pawl and blade guard
The anti-kickback pawl
Re: Bosch GTS1031 10-inch Table Saw
Attached
And the blade guard, too
The blade guard halves move independently of each other
Re: Bosch GTS1031 10-inch Table Saw
The top is not flat. It has a high spot just behind the blade. :thumbdown:
Miter slot is 3/4 inch wide. Compatible with common after-market miter accessories. Like the UHMW-PE miter strip
Or the PTree miter bar
Re: Bosch GTS1031 10-inch Table Saw
Or as a miter t-bar
The included miter gauge is quite decent, but it has some play. Your workpiece can move by half a degree.
Let's move to where the accessories are stored.
The anti-kickback pawls
Miter gauge
Re: Bosch GTS1031 10-inch Table Saw
Blade guard
The kampilan. I mean push stick
The blade wrenches are behind the push stick
Power cord
Re: Bosch GTS1031 10-inch Table Saw
Out of the box, the bevel stops are set to -2 and 47 degrees (or -2 and something other than 45).
I want it to be at 0 and 45. So I set the blade to 0 (or 90) degrees and locked it.
Then I found out that the screw for adjusting the zero positive stop is behind the blade wheel!
But that's not really a problem. I just removed the wheel (via the screw in the middle) so I can access
the positive stop screw.
Now on to the other stop. I set the blade to 45 degrees and locked the blade angle.
Another surprise!
The screw of interest is right behind the blade angle lock lever! This isn't going to be a one-shot so I just left the 45-degree
bevel stop alone for now. I'll come back to it when the need arises.
Re: Bosch GTS1031 10-inch Table Saw
The red power switch in the OFF position
ON position
The power switch has a hole through it for locking. Shown here is the white plastic that came with the unit.
Re: Bosch GTS1031 10-inch Table Saw
Dust port
Height of the table top is a tad over 13 inches. Nearly 2 inches taller than the Chin.
So I have to modify this mobile base after kicking out the Chin out.
Re: Bosch GTS1031 10-inch Table Saw
Dust port
Height of the table top is a tad over 13 inches. Nearly 2 inches taller than the Chin.
So I have to modify this mobile base after kicking out the Chin out.
Way to go brother .... looks like a kid brother of the 4100 ... Bosch US Domestic Market models. :havefun:
Millermatic 180 Autoset Mig Welder
Miller Spoolmate 100 Spool Gun
Victor Firepower 350 Oxy Ace Outfit
3M Speedglas 9002X AD Helmet
Makita LC1230 Dry Cut Saw
Ingersoll Rand Air Tools
Snap On Tools
Metabo Power Tools
Norseman Drill Cutting Tools
Bosch Power Tools
3M PPS
Re: Bosch GTS1031 10-inch Table Saw
Whoa. This one cousin is way better than what the local stores are seling. This is not the same as Jon' s grandprize from the recent bosch contest huh?
This is much like the 4100 but more compact. With every safety features the former has.
Congrats again!
The devil will find work for idle hands to do.-Morrissey
Re: Bosch GTS1031 10-inch Table Saw
@JayL, @V,
I think the major difference compared to the 4100 are limited rip capacity (18 inches) and the absence of soft-start (and electronic speed control).
The rip capacity (left side) can be extended to more than 30 inches by utilizing he router table, which will be level with the TS.
Soft start... I can live without it.
Re: Bosch GTS1031 10-inch Table Saw
Just discovered what the Allen wrenches are for (well, one of them)
Its for removing the bevel lock lever. So you can access the positive stop screw.
Re: Bosch GTS1031 10-inch Table Saw
Are those features i.e. soft start and constant speed control that expensive to be standard features in all universal motors? I am no electromechanical engineer to understand these things. But you guys can make it simpler for me.
Tia
The devil will find work for idle hands to do.-Morrissey
Re: Bosch GTS1031 10-inch Table Saw
@ joey81,
This may be a late one but still CONGRATULATIONS on your new toy but what happens now with the other chin table saw ??? :juggle:
CIGWELD Weldskill 250 amp Mig Welder
AHP Alpha-TIG 200X welder
HITRONIC 300 Amp DC Inverter IGBT Welder
YAMATO 300 amp AC Stick Welder
YAMATO 200 amp DC Inverter IGBT Welder
DeWALT Chopsaw
HOBART and ESAB Welding Helmets
cloned STIHLs
MS 044 chainsaw
MS 070 chainsaw