Forum

Share:
Notifications
Clear all

Hitachi C12RSH

20 Posts
4 Users
0 Reactions
63 Views
(@joey81)
Posts: 1098
Member
Topic starter
 

The Hitachi C12RSH

Manufacturer specifications:
Amps 15
No-Load Speed 3,800 RPM
Blade Diameter 12"
Miter Cutting Range Left 0°-46°
Right 0°-57°
Bevel Cutting Range (R & L) 0°-45°
Tool Dimensions (WxDxH) 23-7/16" x 36-5/8" x 27-15/16"
Tool Weight 63.9 lbs
90° Cross Cut 4-3/16" x 12-1/4" or 4-11/16" x 10-3/16"
45° Miter (L/R) 4-3/16" x 8-5/8" or 4-11/16" x 7-1/16"
45° Bevel (L) 2-3/4" x 12-1/4" or 2-15/16" x 10-3/16"
Compound Cut 45° x 45°(L/L) 2-3/4"x8-5/8" or 2-15/16"x7-1/16"

 
Posted : 11/08/2012 1:59 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: Hitachi C12RSH

Let's start with the feature unique to this SCMS. The slider bars are located to the side of the blade, and are stacked vertically.

It can be locked in front, with the bars sliding out the back

Or, where shop space is limited, locked at the back

In the front lock configuration, you will need 6 more inches of space at the back.

Hitachi says allowing the users to choose between front or rear lock configuration is a great feature. Personally I think its just marketing BS. I don't see any advantage of the front lock over the rear lock configuation. So my saw will be permanently rear-locked:

 
Posted : 11/08/2012 2:08 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: Hitachi C12RSH

Right miter 57 degrees:

Left 45 degrees:

It has detents at 45, 0 and other commonly used miter angles. You can "skip" the detents by pressing this lever:

Micro-adjustment is done by turning this knob:

 
Posted : 11/08/2012 2:09 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: Hitachi C12RSH

You can lock/release the miter angle by turning this one:

A view of the rack-and-pinion mechanism of the micro-adjust

 
Posted : 11/08/2012 2:11 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: Hitachi C12RSH

It comes with one hold-down clamp:

In action:

A view from the back:

Its cumbersome to always lock/unlock the locking nut at the back. So sometimes its difficult to make the hold-down grip. Later I'm going to make an improvised one from a silicone sealant dispenser gun.

 
Posted : 11/08/2012 2:11 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: Hitachi C12RSH

The fences are tall. Good for crown moldings

And they swing out of the way for bevel cuts:

 
Posted : 11/08/2012 2:12 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: Hitachi C12RSH

It comes with a tire wrench

To change tires, firs remove he hub cap

Then press the arbor lock button on the right side

Turn the blade (make sure the tool is not plugged) while pressing the arbor lock button until the blade locks.
Turn the nut (or bolt?) to the direction of blade rotation (this is a left-handed nut/bolt in this case)

 
Posted : 11/08/2012 2:13 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: Hitachi C12RSH

Remove the flange:

Removing the blade is a two-handed affair. I decided against holding the camera with my mouth because its not waterproof.

1-inch arbor

This is already a 90-tooth blade. I replaced the 60-tooth stock one.

The inner flange. Maybe you can fabricate one to be able to use blades with a different arbor size.

 
Posted : 11/08/2012 2:15 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: Hitachi C12RSH

Ikinahihiya yata ng Hitachi ang pangalan nila. Nakatago, eh.

A view of the dust port. I estimate 60% of the dust goes into the dustbag. The other 40% goes all over the place

This is the bevel lock in the lock position

Unlocked

 
Posted : 11/08/2012 2:19 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: Hitachi C12RSH

Bevel micro-adjust knob

Positive stop at zero degrees. Engaged position

Disenganged

 
Posted : 11/08/2012 2:20 pm
(@willyfernando)
Posts: 799
Prominent Member
 

Re: Hitachi C12RSH

This Green Monster is hefty. Ganda! Nagmukhang "Bunso" ung mga green tools ko.

 
Posted : 11/08/2012 4:21 pm
(@willy1467)
Posts: 173
Estimable Member
 

Re: Hitachi C12RSH

Congrats on your new tool bro! Awesome tool!
It's easier to rip wide boards on that scms.:clap1:

 
Posted : 11/08/2012 5:23 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: Hitachi C12RSH

This Green Monster is hefty. Ganda! Nagmukhang "Bunso" ung mga green tools ko.

I call it The Hulk, actually. I wouldn't call it a monster, because you're the one who owns MONSTER TOOLS!

 
Posted : 11/08/2012 10:32 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: Hitachi C12RSH

Let's continue.

This is where the positive stop hits

You adjust it from the other side

The positive stop for left bevel 45 degrees. Notice the "scratch" directly to the top of the bolt. Would have been better if Hitachi designed a "landing pad" instead of just letting it hit wherever it may.

 
Posted : 11/08/2012 11:50 pm
(@joey81)
Posts: 1098
Member
Topic starter
 

Re: Hitachi C12RSH

Depth of cut adjustment

In full cutting depth

Depth limiter in engaged position.

This locks the saw assembly for transport/storage

 
Posted : 11/08/2012 11:52 pm
Page 1 / 2
Share: